Tracking Features:

Total 216 channels: all-in-view, GPS L1/L2/L2C, Fast acquisition channels,

High accuracy velocity measurement. Reflectometry package of QUATTRO-R provides position solution as well as carrier phase and pseudorange data with high temporal resolution. In additional it outputs of I/Q vectors with 200 Hz sampling rate and cloning of two or more detection channels (slave channels). Control and monitoring of the individual receiver channels during an observation is accomplished with JPS commands. The high bandwidth of the USB and Ethernet interfaces allows to handle high rate measurement data from several channels simultaneously.
Data Storage:Up to 2048MB of onboard non-removable memory for data storage

Input/Output:Two high speed RS232 serial ports (up to 460.8 Kbps), Two High speed configurable RS-232/RS422 serial port (up to 460.8 Kbps), High speed USB 2.0 device port (480 Mbps), Full-duplex 10BASE-T/100BASE-TX Ethernet port, Two CAN 2.0 A/B ports, Two 1-PPS outputs synchronized to GPS or UTC, Two Event Marker inputs, MinPad interface: Four external LED drivers, ON/OFF control and External Command inputs, Four Configurable Lodic-Level GPIO ports

Specifications

Physical

Dimensions: 100x120 mm
Weight: 130 g
Connectors: 64 pins for digital, MMCX (jack, edge mount) for antenna

Electrical

On-board power supply accepts any unregulated voltage between +4.5 to +40 Volts
Power consumption: 5.2 Watt

Rev. 1 - 2

Connector type: 64-pin DIN41612 type B Right Angle, AMP p/n 536052-5.
All the RF connectors are MMCX Jack, Edge Mount, AMPHENOL, P/N 908-22100.

Description	Signal Name	Pin #	Pin #	Signal Name	Description
Power Ground	PGND	A1	B1	PGND	Power Ground
+6.0 to +40 VDC Power Input	PWR_IN	A2	B2	PWR_IN	+6.0 to +40 VDC Power Input
Factory use only, must be left open	FUO	A3	B3	COMMSW#	Active Low Command Input (FN Button)
Reserved	-	A4	B4	KA_PWR	Keep-Alive Power Input for Real-Time Clock (+4.5 to +40 VDC, 10µA typ)
External LED Control	LED2_RED	A5	B5	LED1_RED	External LED Control
External LED Control	LED2_GRN	A6	B6	LED1_GRN	External LED Control
Signal Ground	GND	A7	B7	USB_PWR	USB port Power Input line
USB port D- line	USB_D-	A8	B8	USB_D+	USB port D+ line
Serial port A TXD line	TXDA	A9	B9	CTSA	Serial port A CTS line
Serial port A RXD line	RXDA	A10	B10	RTSA	Serial port A RTS line
Serial port C TXD line	TXDC	A11	B11	CTSC	Serial port C CTS line
Serial port C RXD line	RXDC	A12	B12	RTSC	Serial port C RTS line
RS-422 port TXD+ line	TXDD+	A13	B13	TXDD-	RS-422 port TXD- line
RS-422 port RXD+ line	RXDD+	A14	B14	RXDD-	RS-422 port RXD- line
Signal Ground	GND	A15	B15	-	Reserved
Reserved	-	A16	B16	-	Reserved
Serial port B TXD line	TXDB	A17	B17	CTSB	Serial port B CTS line
Serial port B RXD line	RXDB	A18	B18	RTSB	Serial port B RTS line
CAN1 port CAN-H line	CAN1H	A19	B19	CAN1L	CAN1 port CAN-L line
CAN2 port CAN-H line	CAN2H	A20	B20	CAN2L	CAN2 port CAN-L line
Factory use only, must be left open	FUO	A21	B21	-	Reserved
Signal Ground	GND	A22	B22	1PPSA	1 Puls Per Second output A
Signal Ground	GND	A23	B23	1PPSB	1 Puls Per Second output N
Signal Ground	GND	A24	B24	EVENTA	Event input A
Signal Ground	GND	A25	B25	EVENTB	Event input B
Configurable Logic-Level I/O 0 line	GPIO0	A26	B26	GPIO1	Configurable Logic-Level I/O 1 line
Configurable Logic-Level I/O 2 line	GPIO2	A27	B27	GPIO3	Configurable Logic-Level I/O 3 line
Signal Ground	GND	A28	B28	RESET_IN#	Active Low Reset input
Ethernet port TX+ line	LAN_TX+	A29	B29	LAN_TX-	Ethernet port TX- line
Signal Ground	GND	A30	B30	LAN_LED	Ethernet port control for external LED
Ethernet port RX+ line	LAN_RX+	A31	B31	LAN_RX-	Ethernet port RX- line
Active Low input for ON/OFF switch	ONOFFSW#	A32	B32	IRIG_OUT	IRIG port output line

Rev. 3

Connector type: 64-pin DIN41612 type B Right Angle, AMP p/n 536052-5.
All the RF connectors are MMCX Jack, Edge Mount, AMPHENOL, P/N 908-22100.

Description	Signal Name	Pin #	Pin #	Signal Name	Description
Power Ground	PGND	A1	B1	PGND	Power Ground
+6.0 to +40 VDC Power Input	PWR_IN	A2	B2	PWR_IN	+6.0 to +40 VDC Power Input
Factory use only, must be left open	FUO	A3	B3	COMMSW#	Active Low Command Input (FN Button)
Reserved	-	A4	B4	KA_PWR	Keep-Alive Power Input for Real-Time Clock (+4.5 to +40 VDC, 10µA typ)
External LED Control	LED2_RED	A5	B5	LED1_RED	External LED Control
External LED Control	LED2_GRN	A6	B6	LED1_GRN	External LED Control
Signal Ground	GND	A7	B7	USB_PWR	USB port Power Input line
USB port D- line	USB_D-	A8	B8	USB_D+	USB port D+ line
Serial port A TXD line	TXDA	A9	B9	CTSA	Serial port A CTS line
Serial port A RXD line	RXDA	A10	B10	RTSA	Serial port A RTS line
Serial port C: RS232 TXD line or RS422 TX- line	TXDC/TXC-	A11	B11	CTSC/RXC+	Serial port C: RS232 CTS line or RS422 RX+ line
Serial port C: RS232 RXD line or RS422 RX- line	RXDC/RXC-	A12	B12	RTSC/TXC+	Serial port C: RS232 RTS line or RS422 TX+ line
Serial Port D: RS232 RTS line or RS422 TX+ line	RTSD/TXD+	A13	B13	TXDD/TXD-	Serial Port D: RS232 TXD line or RS422 TX- line
Serial Port D: RS232 CTS line or RS422 RX+ line	CTSD/RXD+	A14	B14	RXDD/RXD-	Serial Port D: RS232 RXD line or RS422 RX- line
Signal Ground	GND	A15	B15	-	Reserved
Reserved	-	A16	B16	-	Reserved
Serial port B TXD line	TXDB	A17	B17	CTSB	Serial port B CTS line
Serial port B RXD line	RXDB	A18	B18	RTSB	Serial port B RTS line
CAN1 port CAN-H line	CAN1H	A19	B19	CAN1L	CAN1 port CAN-L line
CAN2 port CAN-H line	CAN2H	A20	B20	CAN2L	CAN2 port CAN-L line
Factory use only, must be left open	FUO	A21	B21	-	Reserved
Signal Ground	GND	A22	B22	1PPSA	1 Puls Per Second output A
Signal Ground	GND	A23	B23	1PPSB	1 Puls Per Second output N
Signal Ground	GND	A24	B24	EVENTA	Event input A
Signal Ground	GND	A25	B25	EVENTB	Event input B
Configurable Logic-Level I/O 0 line	GPIO0	A26	B26	GPIO1	Configurable Logic-Level I/O 1 line
Configurable Logic-Level I/O 2 line	GPIO2	A27	B27	GPIO3	Configurable Logic-Level I/O 3 line
Signal Ground	GND	A28	B28	RESET_IN#	Active Low Reset input
Ethernet port TX+ line	LAN_TX+	A29	B29	LAN_TX-	Ethernet port TX- line
Signal Ground	GND	A30	B30	LAN_LED	Ethernet port control for external LED
Ethernet port RX+ line	LAN_RX+	A31	B31	LAN_RX-	Ethernet port RX- line
Active Low input for ON/OFF switch	ONOFFSW#	A32	B32	IRIG_OUT	IRIG port output line

Environmental

Operating Temperature: -40°C to +80°C
Storage Temperature: -40°C to +85°C
High shock and vibration resistance

泰达光电